Driller: What should be paid attention to when using driller?
Sinker: all the machinery in use will be more careful, and need to pay attention to in the process of the whole period were more, so it is with the rig, in order to make everyone in the operation of the time don't appear problem, then to explain in the practical application of what are the places that we should pay attention to? If you are interested, you can stay and have a look.
Drilling machine in use must be operated by professional personnel, for some non-professional people must not operate. Or you could damage it. Generally speaking, when working, the first thing to do is to choose the location of the well, the wellhead location, with a shovel to dig 30-50cm deep, 10-30cm diameter of the wellhead. Move the installed frame above the wellhead to align it. Generally, the location of the drilling hole requires solid and dense soil surface, and there should be no bricks, gravel, firewood and straw overhead phenomenon below, so as to avoid water seepage, collapse, subsidence and other phenomena in the process of drilling operation, resulting in safety hazards. If you do these things well, you can use a driller. In addition, it should be noted that a reservoir with a diameter of more than 1.5 square meters and a depth of one meter is dug about four meters away from the wellhead, and the pressure pump is hung horizontally in the reservoir with a wooden pole, and the other end of the pump pipe is connected with the water above the drilling machine. As long as the right way to adapt to the drilling machine, there will be no problems, every step here is very important, for the construction personnel also need to do a good job of understanding in advance. There are still do not understand the place to consult customer service staff at any time.
In addition to these places we should pay attention to when the driller is used, the next is when it is started. Here, you need to tighten the drill bit and drill pipe first. The main control hand hoist lifts the head, and the other one is connected to a drill pipe with a drill bit. Another person with hand drill pipe slowly put the drill through the base hole into the drilling hole, vertical righting, start the drill and water pump, drill pipe rotation is driven into the ground. However, what we need to remind you here is that when using the drilling machine, its drill bit rotates clockwise and cannot be reversed, so as not to cause the drill pipe disjointed and sliding. In addition, the driller in use and its on the place for drill pipe is also to pay more attention to. Here you need to understand that point is scored after section pipe, with people close the insurance clasp, plug in unloading rod card, master machinist reverse the drill stem counterclockwise, lift the nose with drill pipe separation, improve the nose, with people in a drill pipe, other manual rotation wire connection on the top of the head, the bottom on the butt joint, master machinist boot clockwise will drill pipe tighten, Open the safety card, take off the unloading rod card, start the machine clockwise rotation, continue drilling. Repeat the above action over and over again. As long as there is no problem in these places, then when you use it, you will often fail.
After the introduction of the above content, you will find that in fact, this driller should pay attention to more places when using it. I hope we can understand it after seeing it. Please feel free to contact us if you need anything. There are also professional customer service staff 24 hours for you, you can always ask them if you have any questions.
Shijiazhuang Compus Compressor Co., Ltd. main products are oil-free air compressor, high pressure air compressor, screw air compressor, air compressor, drilling air compressor, oil-free mobile machine, high pressure mobile machine, drilling machine, two-stage compression screw machine, permanent magnet variable frequency screw machine, mine explosion-proof screw machine, air floating centrifugal blower and so on. At present, the company has established 30 customer service networks and more than 100 dealers in the country, to provide customers with pre-sales technical consultation, machine sales, on-site maintenance, parts supply 4S services. The enterprise's good faith service is well received by users. Adhering to the core concept of "quality first, customer satisfaction", we always adhere to provide customers with high-quality products and technical services, we firmly believe that Compus will become your more reliable partner, and are willing to work with you to achieve glory!